NanoStructures Laboratory - User contributions [en]

E-Line Calendar/E-Line/7-6-2012 -Event 1

2012-07-06T10:51:08Z

Ema085: Blanked the page

E-Line Calendar/E-Line/7-6-2012 -Event 1

2012-07-06T09:34:33Z

Ema085:

Erik (12:30 :14:00)

E-Line Calendar/E-Line/7-6-2012 -Event 1

2012-07-05T14:36:32Z

Ema085: Created page with 'Erik (12:00 :14:00)'

Erik (12:00 :14:00)

Main Page

2012-07-04T10:54:51Z

Ema085:

= Wiki for UiB's NanoStructures Laboratory. =

UiB's NanoStructures laboratory is equipped with modern thin-film processing and lithography equipment. The lab is built around an electron-beam lithography tool (Raith e-Line) which can be used to pattern resist thin-films with minimal structure sizes of the order of 10 nanometer. The resist layers can be used to transfer the pattern into other thin-films that are either deposited using an electron-beam evaporator (Temescal FC-2000) or a spin-coater. For the pattern transfer a reactive-ion etcher (RIE, Plasmatherm 790+) is available as well as a wet-bench fumehood to perform wet-etch and lift-off processes. An improvised UV-exposure setup is available for crude patterning.

We use this WikiMedia site for documentation of all equipment, facilities and standard operating procedures of the laboratory. As a registered user of the laboratory you will receive permission to log into this site, which will allow you to contribute to the documentation and give information on the processes particular to your project.

== Equipment and Standard Operating Procedures (SOPs)==

* Electron-beam lithography: Raith e-Line
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[E-Line Calendar|e-Line Reservation Calendar]]
** SOP: [[File:SOP_Raith_E-Line.doc||e-Line SOP]]
** Maintenance: [[File:SOP_Raith_E-Line_Maintenance.doc||e-Line Maintenance SOP]]

* Reactive-ion etcher: Plasmatherm 790+
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Plasmatherm Calendar|Plasmatherm Reservation Calendar]]
** SOP: [[File:SOP_Plasmatherm.doc||Plasmatherm 790+ SOP]]
** Maintenance: [[File:SOP_Plasmatherm_Maintenance.doc||Plasmatherm 790+ Maintenance SOP]]

* Electron-beam evaporator: Temescal FC-2000
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Temescal Calendar|Temescal FC-2000 Reservation Calendar]]
** SOP: [[File:SOP_Temescal.doc||Temescal FC-2000 SOP]]
** Maintenance: [[File:SOP_Temescal_Maintenance.doc||Temescal FC-2000 Maintenance SOP]]

* UV-lithography setup

* Spin-coater
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[Spin Coater Calendar|Spin Coater Reservation Calendar]]
** SOP: [[File:SOP_SpinCoater.doc||Spin Coater SOP]]

* Convection Oven
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Convection Oven Calendar|Convection Oven Reservation Calendar]]
** SOP: [[File:SOP_convectionoven.doc||Convection Oven SOP]]

* Hotplates

* Ultrasonic Bath

* Sputter coater
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Sputter Coater|Sputter Coater Reservation Calendar]]
** SOP: [[File:SOP_Sputter_Coater||Sputter Coater SOP]]

* Thin-film characterization: Filmetrics F-10
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[Filmetrics F-10 Calendar|Filmetrics F-10 Reservation Calendar]]
** SOP: [[File:SOP_Filmetrics.doc||Filmetrics F-10 SOP]]

* [[Cleanroom|ISO-class 5 cleanroom]]
* [[Fumehood Cleanroom|Cleanroom Fumehood]]
* [[Fumehood Outerlab|Outerlab Fumehood]]

* Lift-off

* Chrome wet-etch
** Owner: [[Erik|Erik Mannseth]]
** SOP: [[File:SOP_chromewetech.doc||Chrome wet-etch SOP]]

* old link: [[Procedures|Standard Operating Procedures]]
* old link: [[Tools|Available fabrication tools and facilities]]

== Facilities ==

Here is a description of the available facilities: [[File:Facilities.doc||Facilities Documentation]].

Here is a summary of the maintenance documents: [[File:Facilities_Maintenance.doc||Facilities Maintenance Documentation]].

* [[DI-Water|De-ionized water unit]]
* [[Neutralizer|Waste Water Neutralizer]]
* [[Scrubber|Exhaust Scrubber for fumehood exhaust]]
* [[Cooling Water|Cooling Water]]
* [[Nitrogen|Nitrogen 5.0 Pressure Swing Adsorption Unit]]
* [[Electricity|Information on Electricity]]
* [[Air Conditioning|Air Conditioning]]
* [[Pressurized Air|Pressurized Air]]
* [[Chemical Storage|Storage for Chemicals]]

== Laboratory Documents ==

* [[Rules|Laboratory Code of Conduct / Clothing rules]]
* [[Safety|Safety Guidelines and Information]]
* [[Cleaning|Lab Cleaning Procedures]]
* [[Consumables|Available consumables and supplier information]]

== People ==

* [[Bodil|Bodil Holst]]
* [[Bjoern|Bjørn Samelin]]
* [[Thomas R|Thomas Reisinger]]
* [[Erik|Erik Mannseth]]
* [[Xiaodong|Xiaodong Guo]]
* [[Martin|Martin Greve]]
* [[Rachid|Rachid Maad]]
* [[Thomas B|Thomas Bolstad]]
* [[Thomas H|Thomas Håvardstun]]
* [[Jarand|Jarand Gauteplass]]

== Further Information ==

There is a huge amount of information on Micro- and Nanofabrication on the web. Here are just some examples:

* MIT open courseware on nano processing [http://ocw.mit.edu/courses/electrical-engineering-and-computer-science/6-152j-micro-nano-processing-technology-fall-2005/]
* Resources at Chalmers (Swedish Nano-processing lab)[http://www.chalmers.se/mc2/EN/laboratories/nanofabrication/education-training/micro-nanoprocessing]
* Useful recipes at Brigham Young University [http://www.cleanroom.byu.edu/]
* Wikibook on Microtechnology [http://en.wikibooks.org/wiki/Microtechnology]

= Information on using MediaWiki =

* [http://www.mediawiki.org/wiki/Manual:Configuration_settings Configuration settings list]
* [http://www.mediawiki.org/wiki/Manual:FAQ MediaWiki FAQ]
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list]

Consult the [http://meta.wikimedia.org/wiki/Help:Contents User's Guide] for information on using the wiki software.

Main Page

2012-07-04T10:54:08Z

Ema085:

= Wiki for UiB's NanoStructures Laboratory. =

UiB's NanoStructures laboratory is equipped with modern thin-film processing and lithography equipment. The lab is built around an electron-beam lithography tool (Raith e-Line) which can be used to pattern resist thin-films with minimal structure sizes of the order of 10 nanometer. The resist layers can be used to transfer the pattern into other thin-films that are either deposited using an electron-beam evaporator (Temescal FC-2000) or a spin-coater. For the pattern transfer a reactive-ion etcher (RIE, Plasmatherm 790+) is available as well as a wet-bench fumehood to perform wet-etch and lift-off processes. An improvised UV-exposure setup is available for crude patterning.

We use this WikiMedia site for documentation of all equipment, facilities and standard operating procedures of the laboratory. As a registered user of the laboratory you will receive permission to log into this site, which will allow you to contribute to the documentation and give information on the processes particular to your project.

== Equipment and Standard Operating Procedures (SOPs)==

* Electron-beam lithography: Raith e-Line
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[E-Line Calendar|e-Line Reservation Calendar]]
** SOP: [[File:SOP_Raith_E-Line.doc||e-Line SOP]]
** Maintenance: [[File:SOP_Raith_E-Line_Maintenance.doc||e-Line Maintenance SOP]]

* Reactive-ion etcher: Plasmatherm 790+
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Plasmatherm Calendar|Plasmatherm Reservation Calendar]]
** SOP: [[File:SOP_Plasmatherm.doc||Plasmatherm 790+ SOP]]
** Maintenance: [[File:SOP_Plasmatherm_Maintenance.doc||Plasmatherm 790+ Maintenance SOP]]

* Electron-beam evaporator: Temescal FC-2000
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Temescal Calendar|Temescal FC-2000 Reservation Calendar]]
** SOP: [[File:SOP_Temescal.doc||Temescal FC-2000 SOP]]
** Maintenance: [[File:SOP_Temescal_Maintenance.doc||Temescal FC-2000 Maintenance SOP]]

* UV-lithography setup

* Spin-coater
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[Spin Coater Calendar|Spin Coater Reservation Calendar]]
** SOP: [[File:SOP_SpinCoater.doc||Spin Coater SOP]]

* Convection Oven
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Convection Oven Calendar|Convection Oven Reservation Calendar]]
** SOP: [[File:SOP_convectionoven.doc||Convection Oven SOP]]

* Hotplates

* Ultrasonic Bath

* Sputter coater
** Owner: [[Xiaodong|Xiaodong Guo]]
** Reservation: [[Sputter Coater|Sputter Coater Reservation Calendar]]
** SOP: [[File:||Sputter Coater SOP]]

* Thin-film characterization: Filmetrics F-10
** Owner: [[Erik|Erik Mannseth]]
** Reservation: [[Filmetrics F-10 Calendar|Filmetrics F-10 Reservation Calendar]]
** SOP: [[File:SOP_Filmetrics.doc||Filmetrics F-10 SOP]]

* [[Cleanroom|ISO-class 5 cleanroom]]
* [[Fumehood Cleanroom|Cleanroom Fumehood]]
* [[Fumehood Outerlab|Outerlab Fumehood]]

* Lift-off

* Chrome wet-etch
** Owner: [[Erik|Erik Mannseth]]
** SOP: [[File:SOP_chromewetech.doc||Chrome wet-etch SOP]]

* old link: [[Procedures|Standard Operating Procedures]]
* old link: [[Tools|Available fabrication tools and facilities]]

== Facilities ==

Here is a description of the available facilities: [[File:Facilities.doc||Facilities Documentation]].

Here is a summary of the maintenance documents: [[File:Facilities_Maintenance.doc||Facilities Maintenance Documentation]].

* [[DI-Water|De-ionized water unit]]
* [[Neutralizer|Waste Water Neutralizer]]
* [[Scrubber|Exhaust Scrubber for fumehood exhaust]]
* [[Cooling Water|Cooling Water]]
* [[Nitrogen|Nitrogen 5.0 Pressure Swing Adsorption Unit]]
* [[Electricity|Information on Electricity]]
* [[Air Conditioning|Air Conditioning]]
* [[Pressurized Air|Pressurized Air]]
* [[Chemical Storage|Storage for Chemicals]]

== Laboratory Documents ==

* [[Rules|Laboratory Code of Conduct / Clothing rules]]
* [[Safety|Safety Guidelines and Information]]
* [[Cleaning|Lab Cleaning Procedures]]
* [[Consumables|Available consumables and supplier information]]

== People ==

* [[Bodil|Bodil Holst]]
* [[Bjoern|Bjørn Samelin]]
* [[Thomas R|Thomas Reisinger]]
* [[Erik|Erik Mannseth]]
* [[Xiaodong|Xiaodong Guo]]
* [[Martin|Martin Greve]]
* [[Rachid|Rachid Maad]]
* [[Thomas B|Thomas Bolstad]]
* [[Thomas H|Thomas Håvardstun]]
* [[Jarand|Jarand Gauteplass]]

== Further Information ==

There is a huge amount of information on Micro- and Nanofabrication on the web. Here are just some examples:

* MIT open courseware on nano processing [http://ocw.mit.edu/courses/electrical-engineering-and-computer-science/6-152j-micro-nano-processing-technology-fall-2005/]
* Resources at Chalmers (Swedish Nano-processing lab)[http://www.chalmers.se/mc2/EN/laboratories/nanofabrication/education-training/micro-nanoprocessing]
* Useful recipes at Brigham Young University [http://www.cleanroom.byu.edu/]
* Wikibook on Microtechnology [http://en.wikibooks.org/wiki/Microtechnology]

= Information on using MediaWiki =

* [http://www.mediawiki.org/wiki/Manual:Configuration_settings Configuration settings list]
* [http://www.mediawiki.org/wiki/Manual:FAQ MediaWiki FAQ]
* [https://lists.wikimedia.org/mailman/listinfo/mediawiki-announce MediaWiki release mailing list]

Consult the [http://meta.wikimedia.org/wiki/Help:Contents User's Guide] for information on using the wiki software.

E-Line Calendar/E-Line/6-28-2012 -Event 1

2012-06-27T14:52:47Z

Ema085:

Erik (12:30 - 14:30)

E-Line Calendar/E-Line/6-28-2012 -Event 1

2012-06-27T13:25:26Z

Ema085:

Erik (11:30 - 14:00)

E-Line Calendar/E-Line/6-28-2012 -Event 1

2012-06-27T13:25:17Z

Ema085: Created page with 'Erik (11:00 - 14:00)'

Erik (11:00 - 14:00)

E-Line Calendar/E-Line/6-8-2012 -Event 1

2012-06-07T14:44:10Z

Ema085:

Erik (14:00-17:00)

E-Line Calendar/E-Line/6-8-2012 -Event 1

2012-06-07T14:44:03Z

Ema085: Created page with 'Erik (14:00-16:00)'

Erik (14:00-16:00)

E-Line Calendar/E-Line/6-7-2012 -Event 1

2012-06-07T08:42:56Z

Ema085:

Erik (13:00-17:00)

E-Line Calendar/E-Line/6-7-2012 -Event 1

2012-06-06T13:36:55Z

Ema085:

Erik (12:00-17:00)

E-Line Calendar/E-Line/6-7-2012 -Event 1

2012-06-06T13:36:42Z

Ema085: Created page with '12:00-17:00'

12:00-17:00

File:SOP chromewetech.doc

2012-06-04T16:09:44Z

Ema085:

File:SOP SpinCoater.doc

2012-06-04T16:03:30Z

Ema085:

File:SOP Filmetrics.doc

2012-06-04T16:02:57Z

Ema085:

File:SOP SputterCoater.doc

2012-06-04T16:02:12Z

Ema085:

E-Line Calendar/E-Line/5-14-2012 -Event 2

2012-05-14T11:30:50Z

Ema085:

Erik (15:00-17:00)

E-Line Calendar/E-Line/5-14-2012 -Event 2

2012-05-14T10:21:25Z

Ema085: Created page with 'Erik (14:00-16:00)'

Erik (14:00-16:00)

Cleaning

2012-05-07T12:34:48Z

Ema085: /* Waste disposal */

==Waste disposal==

When a bottle is filled with chemical waste it needs to be delt with approriatly.

For the most normal waste solvents(aceton, isopropanol, methanol) the bottles should be delivered to room 222, with a filled out chemical waste form.

Cleaning

2012-05-07T12:33:35Z

Ema085:

==Waste disposal==

When a bottle is filled with chemical waste it needs to be delt with approriatly.

For then most normal waste solvents(aceton, isopropanol, methanol) bottles the bottles should be delivered to room 222, with a filled out chemical waste form.
Bellow
[[File:Waste_desposal_form(filled_out_for_solvents).pdf‎||Waste desposal form for common solvents]]

File:Waste desposal form(filled out for solvents).pdf

2012-05-07T12:32:40Z

Ema085: waste desposal form

waste desposal form

Cleaning

2012-05-07T12:31:39Z

Ema085:

==Waste disposal==

When a bottle is filled with chemical waste it needs to be delt with approriatly.

For then most normal waste solvents(aceton, isopropanol, methanol) bottles the bottles should be delivered to room 222, with a filled out chemical waste form.
Bellow
[[File:SOP_Raith_E-Line_Maintenance.doc||e-Line Maintenance SOP]]

Cleaning

2012-05-07T12:30:28Z

Ema085: /* Waist desposal */

Cleaning

2012-05-07T12:28:02Z

Ema085: Created page with '==Waist desposal=='

==Waist desposal==

E-Line Calendar/E-Line/5-4-2012 -Event 1

2012-05-03T12:11:46Z

Ema085: Created page with 'Erik: (10:00-15:00)'

Erik: (10:00-15:00)

E-Line Calendar/E-Line/5-2-2012 -Event 1

2012-05-02T08:45:02Z

Ema085: Created page with 'Erik: (12:30-16:00) laser repair with raith.'

Erik: (12:30-16:00) laser repair with raith.

E-Line Calendar/E-Line/5-1-2012 -Event 1

2012-04-29T13:12:31Z

Ema085: Blanked the page

E-Line Calendar/E-Line/5-3-2012 -Event 1

2012-04-29T13:11:43Z

Ema085: Created page with 'Erik (11:00-15:00)'

Erik (11:00-15:00)

E-Line Calendar/E-Line/5-1-2012 -Event 1

2012-04-29T12:19:57Z

Ema085: Created page with 'Erik (11:00-15:00)'

Erik (11:00-15:00)

E-Line Calendar/E-Line/3-30-2012 -Event 1

2012-03-29T15:35:19Z

Ema085: Created page with 'Erik (11:00-14:00) - changing pre vacuum pump.'

Erik (11:00-14:00) - changing pre vacuum pump.

E-Line Calendar/E-Line/3-22-2012 -Event 1

2012-03-20T14:24:15Z

Ema085: Created page with 'erik 14:00 17:00'

erik 14:00 17:00

H-F Antidote

2012-03-19T11:17:54Z

Ema085:

==How to use==

Directions for use: It is important to treat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

Make sure to check the expiration date of the H-F Antidote. If it is close to the expiration date(or expired) a new supply should be bought.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". The webpage uib.no/hms is for the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:16:42Z

Ema085:

==How to use==

Directions for use: It is important to treat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

Make sure to check the expiration date of the H-F Antidote. If it is close to expiring (or expired) a new supply should be bought.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". The webpage uib.no/hms is for the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:14:30Z

Ema085:

==How to use==

Directions for use: It is important to treat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". The webpage uib.no/hms is for the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:14:08Z

Ema085:

==How to use==

Directions for use: It is important to treat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". This is the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:13:12Z

Ema085:

==How to use==

Directions for use: It is important to treat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". This is the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:07:04Z

Ema085:

==How to use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege". This is the health and safty department of UiB.

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:06:18Z

Ema085:

==How to use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Name: Antic, Ruza
*Title: bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege".

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:06:01Z

Ema085:

==How to use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

*Antic, Ruza
*bedriftslege
*Tlf: 55 58 20 54
*E-mail: Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege".

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:05:25Z

Ema085:

==How to use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

Antic, Ruza
bedriftslege
Tlf: 55 58 20 54
Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege".

You need a prescription and the pharmacy will need to order the H-F antidote so you can not get it the same day. In addition the H-F antidote costs around 1500kr so you might want a requisition from the finacial department of IFT so you do not have to pay for it yourself.

H-F Antidote

2012-03-19T11:01:30Z

Ema085:

==How to use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

==How to aquire==

H-F antidote is bought from the pharmacy (http://www.vitusapotek.no/), closest one is at Bergen Storesenter. You will need a prescription from a doctor. The UiB doctor will provide this. For now the contact information for the UiB doctor is

Antic, Ruza
bedriftslege
Tlf: 55 58 20 54
Ruza.Antic@adm.uib.no

This could change in the future, but the you can find the doctor on this page (http://www.uib.no/hms/kontakt/ansattkatalog) with the title "bedriftslege".

You need a http://www.uib.no/hms/kontakt/ansattkatalog

H-F Antidote

2012-03-19T10:57:36Z

Ema085:

H-F Antidote

2012-03-19T10:57:10Z

Ema085:

==H-F Antidote use==

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

H-F Antidote

2012-03-19T10:56:52Z

Ema085: Created page with 'HF-antidote use: Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast o…'

HF-antidote use:

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

Safety

2012-03-19T10:56:22Z

Ema085:

* [[H-F Antidote|H-F Antidote information]]

H-F

2012-03-19T10:55:54Z

Ema085:

=H-F Antidote=

==H-F Antidote Use==
Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

H-F

2012-03-19T10:54:32Z

Ema085:

--HF-antidote use--

Directions for use: It is important to tereat Hydrofluoric Acid burns at once. Immediately wash of the affected area with copious amounts of water for atleast one minute. Carefully remove contaminated clothing taking care not to contaminate further areas of skin. Apply H-F Antidote gel on and around the affected area with gentle massage. Seek medical attention. Continue to massage the gel into the affected area, using repeated applications until 15 minutes after the pain has subsided, or until medical treatment is available. If, after medical treatment, pain should re-occur at the burn site, re-applay the H-F Antidote Gel and seek further medical attention at once.

Precautions: In all cases lf Hydrofluoric Acid burns, it is important to use this First Aid treatment without delay. There are no known contraindications for use, or interactions with other products. Discard all opend tubes of H-F Antidote Gel after treatment.

H-F

2012-03-19T10:54:04Z

Safety

2012-03-19T10:53:30Z

Ema085:

* [[H-F|H-F Antidote information]]