Temescal FC-2000 Electron-beam Evaporator - Revision history

Ema085: /* How to replace crystals */

2012-01-17T12:02:17Z

How to replace crystals

← Older revision		Revision as of 12:02, 17 January 2012
Line 51:		Line 51:

	====How to replace crystals====		====How to replace crystals====

			Press vent PC (product chamber) in the auto menu. When the PC is at atmosfare you can open the the lid. Inside the "bowl" close to the front of the machin there are two flat circular metal rings(insert image) one of which is coverd by a metal screen. These are the depisition hight measurment crystals.

	===STOP Digital input===		===STOP Digital input===

	If you see this message on the deposition control screen, I am not sure what to do, I am trying to fix this error now(05.01.2012).		If you see this message on the deposition control screen, I am not sure what to do, I am trying to fix this error now(05.01.2012).

Tre043: /* Procedure: Turn on */

2012-01-09T15:40:13Z

Procedure: Turn on

← Older revision		Revision as of 15:40, 9 January 2012
Line 28:		Line 28:
	# Switch on circuit breakers at back of electronics rack (inside panel-door), in the order left-to-right		# Switch on circuit breakers at back of electronics rack (inside panel-door), in the order left-to-right
	# Wait until computer starts up, start up Temescal software		# Wait until computer starts up, start up Temescal software
	# Log on		# Log on (service:factory)
			# In the service pane go to Source 1. Set Ebeam Emission Current Scale to 1500mA.
	# Regenerate Cryopump		# Regenerate Cryopump





	==Typical problems with the Temescal FC-2000==		==Typical problems with the Temescal FC-2000==

Ema085: /* Crystal fail */

2012-01-05T12:06:19Z

Crystal fail

← Older revision		Revision as of 12:06, 5 January 2012
Line 51:		Line 51:
	===Crystal fail===		===Crystal fail===

	If a red message of crystal fail appers in the TCX(deposition control screen) try changing the crystal number in use. This is done by pressing menu and then navigate to sensor. Press menu when on the sensor button. You should now be in the sensor information menu. Press 1(togle) on the panel to change between crystals 1 and 2. If both crystals give crystal fail the crystals need to be physically replaced in the machin.		If a red message of crystal fail appers in the TCX (deposition control screen) try changing the crystal number in use. This is done by pressing menu and then navigate to sensor. Press menu when on the sensor button. You should now be in the sensor information menu. Press 1 (togle) on the panel to change between crystals 1 and 2. If both crystals give crystal fail the crystals need to be physically replaced in the machin.

	====How to replace crystals====		====How to replace crystals====

Ema085: /* Typical problems with the Temescal FC-2000 */

2012-01-05T12:05:35Z

Typical problems with the Temescal FC-2000

← Older revision		Revision as of 12:05, 5 January 2012
Line 48:		Line 48:
	#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.		#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.
	#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.		#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.

			===Crystal fail===

			If a red message of crystal fail appers in the TCX(deposition control screen) try changing the crystal number in use. This is done by pressing menu and then navigate to sensor. Press menu when on the sensor button. You should now be in the sensor information menu. Press 1(togle) on the panel to change between crystals 1 and 2. If both crystals give crystal fail the crystals need to be physically replaced in the machin.

			====How to replace crystals====

			===STOP Digital input===

			If you see this message on the deposition control screen, I am not sure what to do, I am trying to fix this error now(05.01.2012).

Tre043: moved Temescal Electron-beam Evaporator to Temescal FC-2000 Electron-beam Evaporator

2011-11-07T15:48:05Z

moved Temescal Electron-beam Evaporator to Temescal FC-2000 Electron-beam Evaporator

← Older revision	Revision as of 15:48, 7 November 2011
(No difference)

Tre043 at 15:47, 7 November 2011

2011-11-07T15:47:39Z

@@ Line 1: / Line 1: @@
 [[File:Evaporation_tool.JPG|thumb|]]
-==Normal problems with the Temescal==
 ===TC pump wont turn on===
@@ Line 14: / Line 48: @@
 #In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.
 #To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.

Ema085: /* How to regenerate the system */

2011-10-18T15:08:28Z

How to regenerate the system

← Older revision		Revision as of 15:08, 18 October 2011
Line 11:		Line 11:
	#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).		#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).
	#Press detail in the upper right corner(see [[:File:temescal_GUI_2.JPG\|Interface for the Temescal]]).		#Press detail in the upper right corner(see [[:File:temescal_GUI_2.JPG\|Interface for the Temescal]]).
	#When detail is pressed click on the cryopump (see [[:File:temescal_GUI.JPG\|Interface for the Temescal,with regen menu up]]).		#When detail is pressed click on the cryopump (see [[:File:temescal_GUI.JPG\|Interface for the Temescal, with regen menu up]]).
	#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.		#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.
	#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.		#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.

	=== Anything else?===		=== Anything else?===

Ema085: /* How to regenerate the system */

2011-10-18T15:07:43Z

How to regenerate the system

← Older revision		Revision as of 15:07, 18 October 2011
Line 10:		Line 10:

	#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).		#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).
	#Press detail in the upper right corner(see [[File:~~temescal_GUI~~.JPG\|~~thumb\|~~]]).		#Press detail in the upper right corner(see [[:File:temescal_GUI_2.JPG\|Interface for the Temescal]]).
	#When detail is pressed click on the cryopump (~~insert image~~).		#When detail is pressed click on the cryopump (see [[:File:temescal_GUI.JPG\|Interface for the Temescal,with regen menu up]]).
	#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.		#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.
	#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.		#To see that it finished look at the crypump again, the stage two temperature should be around 11 kelvin and the TC should be on.

	=== Anything else?===		=== Anything else?===

Ema085: /* How to regenerate the system */

2011-10-18T15:06:26Z

How to regenerate the system

← Older revision		Revision as of 15:06, 18 October 2011
Line 10:		Line 10:

	#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).		#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).
	#Press detail in the upper right corner(see [[File:temescal_GUI.JPG]]).		#Press detail in the upper right corner(see [[File:temescal_GUI.JPG\|thumb\|]]).
	#When detail is pressed click on the cryopump (insert image).		#When detail is pressed click on the cryopump (insert image).
	#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.		#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.

Ema085: /* How to regenerate the system */

2011-10-18T15:06:10Z

How to regenerate the system

← Older revision		Revision as of 15:06, 18 October 2011
Line 10:		Line 10:

	#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).		#Go to system map on the Temescal computer(see [[:File:Evaporation_computer.JPG\|Temescal computer]]).
	#Press detail in the upper right corner(~~insert image~~).		#Press detail in the upper right corner(see [[File:temescal_GUI.JPG]]).
	#When detail is pressed click on the cryopump (insert image).		#When detail is pressed click on the cryopump (insert image).
	#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.		#In the menu that pops up press regen SC, this should start the regenration prosses. It will take around 6 hours to finish.